What you'll need... Step 1. Take a spool of skinned hooklink and a stripper tool. Step 2. Using a stripper tool, strip back around 5 inches of coating. Step 3. Tie a simple double overhand loop to form a hair. Step 4. Tie a simple knotless [...]

What you'll need... Step 1. Start off by threading the Trip Wire through the eye of a Chod Hook this way. Step 2. Create a loop - it may need to be larger so you can whip it up the hook shank. Step 3. When it comes to [...]

What you'll need... Step 1. Tie a size 11 or 12 Mugga on with a knotless knot and 'blob' the tag (optional). Step 2. Using a sewing needle pierce the rubber grub (orientation as shown)... Step 3. ...and carefully thread it onto your hooklink. Step 4. Push the grub over [...]

What you'll need... Step 1. Skinned hooklinks are perfect for tying Multi-Rigs. We've chosen Sly Skin as it's the stiffest skinned hooklink in the GT range. Cut off 6 inches more than the finished hooklink. Step 2. Form a Fig.8 loop knot at both ends. Make sure the loop at [...]

What you'll need... Step 1. Start off by tying a 3mm loop and tying a size 12 Mugga hook on with a 6 turn whipping knot. It's important you keep the overall hair about 5mm. Step 2. Cut off a small section of Zig Rig Foam. About 1cm is ample [...]

What you'll need... Step 1. Start off by attaching the Long Shank Mugga to the Vigilante with a simple knotless knot. Step 2. Trim off excess as the hookbait will be mounted on a rig ring, not a hair. Step 3. Push 1cm of 0.5mm silicon tubing up [...]

What you'll need... Step 1. Place hookbait in the corner of the bag. Step 2. Cover with half an inch of mix, position lead and cover with more mix. Step 3. Keep tapping the bag so the mix settles (add PVA friendly liquids now). Step 4. [...]

What you'll need... Step 1. Start of with a knotless knot - for D-rigged bottom baits and our chod rig about 9 turns is about right. Step 2. Put on a small Covert Rig Ring. Step 3. Create 'D' by looping the hair with the rig ring back [...]

What you'll need... Step 1. Strip 10cm of Sly Skin. Step 2. Start the KD rig with 7 turns up the shank. Step 3. Fold back the hair and whip a couple more turns round the hook. Step 4. The finished hook and hair should look [...]

What you'll need... Step 1. Strip 10cm of Sly Skin. Step 2. Using the exposed supple section form a simple hair loop. Step 3. Fold back the hair and whip a couple more turns round the hook. Step 4. Measure the hook length to the correct [...]

What you'll need... Step 1. Using a Peel and Pull stripper tool remove around 3 inches of coating. Step 2. Tie a small loop in the end of the stripped braid and attach a 12mm pop-up. Step 3. Secure the pop-up to a size 8 Covert Continental Mugga [...]

What you'll need... Step 1. Using a Peel and Pull stripper tool remove around 3 inches of coating. Step 2. Tie a small loop in the end to retain the hair stop when the rig is finished. Step 3. Tie a small loop in the end. [...]

What you'll need... Step 1. Start off by tying a small loop in the end of a length of your chosen monofilament hooklink. Step 2. Thread the hooklink through the eye so that the hair is on the outside of the hook... Step 3. ...and whip the hooklink [...]

Step 1. Using a Gardner Stripper tool peel back several inches of braid. Step 2. Cut off the tag end. Step 3. Tie on a Covert Ring Ring using an overhand knot. Step 4. Attached a size 8 Covert Mugga hook using knotless knot with the rig ring [...]